Products | Laser Center/Edge Finder

Battery Powered Mini LC/EF – 6 mm Shank – Dot

$124.50
6 mm Shank is made for mini tabletop mills/lathes

3" overall length (without polarizer)

3/4" overall diameter

Uses three common LR44 batteries (included)

Repeatable Accuracy of .001" (estimated)

Includes polarizing attachment to minimize the size of the dot

The Laser Center/Edge Finder™ is a tool for your mini tabletop mills/lathe, which saves setup time. It eliminates the frustrations and doubts of using the century-old indirect method with a conventional edge finder or wiggler. The Laser Center/Edge Finder™ projects a fine laser beam that directly indicates the edge of the workpiece. Move the beam to the edge of the work and set your dial to zero. It is that easy. No more calculating half the diameter of the edge finder. You can also use the Laser Center/Edge Finder™ to locate scribed or center-punched locations. Simply move the laser beam to the location on the workpiece and the spindle is aligned. The Laser Center/Edge Finder™ is easy to align, using the four alignment screws, so you can be sure it is always accurate. . A target card and allen wrench are included to help with alignment. The batteries last for over 3 hours of continuous operation. That's about 6 months to a year of normal use.
Add to cart Details
Magnetic Holder

$11.50
Fits all Laser Center/Edge Finder™ models except the Bridgemount models.

The Magnetic Holder was developed as a way to store the LC/EF close at hand on the mill and keep it from getting damaged from rolling off the table onto the floor. It can be applied to any magnetic surface. The LC/EF fits into the holder, upside down, with the polarizer still attached. By having the LC/EF upside down in the holder and aimed just above the operator's head, the operator can observe if the battery powered LC/EF is left on. This would keep the batteries from running down too fast.
Add to cart Details
Polarizer Attachment – Single

$28.00
Fits all Laser Center/Edge Finder™ models that project a dot

Included on all models projecting the laser dot

The LC/EF Polarizing Attachment was developed to control the size of the laser dot, making viewing easier and more accurate on a variety of surfaces. This is accomplished by the addition of a linear polarizer element to effectively control the intensity of the laser beam. The lower intensity beam is easier for the human visual system to view, especially on reflective surfaces. The polarizer simply slips over the nose of the LC/EF. Rotating the polarizer in either direction will minimize the size of the laser dot projected
Add to cart Details
Replacement Power Supply – Push-in

$22.50

This replaces any power supply that has the push-in receptacle.

Add to cart Details
Battery Powered Original LC/EF – 3/8″ Shank – Concentric Circle

$164.50
3/8" Shank is made for standard sized mills and lathes

3.375" overall length (without polarizer)

3/4" overall diameter

Uses three common LR44 batteries (included)

Repeatable Accuracy of .001" (estimated)

Includes dual polarizing attachment to minimize the thickness of the lines

The Laser Center/Edge Finder™ is a tool for your standard size mill, lathe or drill press which saves setup time. It eliminates the frustrations and doubts of using the century-old indirect method with a conventional edge finder or wiggler. The Laser Center/Edge Finder™ projects a series of concentric rings, making it easy to center over an existing hole.. The unit comes with a dual polarizer attached to allow the user to minimize the thickness of the lines for added accuracy. The Laser Center/Edge Finder™ is easy to align, using the four alignment screws, so you can be sure it is always accurate. A target card and allen wrench are included to help with alignment. The batteries last for over 3 hours of continuous operation. That's about 6 months to a year of normal use.
Add to cart Details
Battery Powered Wet Cabinet CNC – 1/2″Shank – Dot

$134.50
1/2" shank is made for wet cabinet CNC machines

3.375" overall length (without polarizer or boot)

3/4" overall diameter

Uses three common LR44 batteries (included)

Repeatable Accuracy of .001" (estimated)

Includes polarizing attachment to minimize the size of the dot

Includes vinyl boot

The Laser Center/Edge Finder™ is a tool for your CNC machine that saves setup time. It eliminates the frustrations and doubts of using the century-old indirect method with a conventional edge finder or wiggler. The vinyl boot and machined flange on this model create a water-proof seal. The boot slides over the Laser Center/Edge Finder™ (with the polarizer removed) so you can leave it in your cabinet CNC tool rack. The Laser Center/Edge Finder™ projects a fine laser beam that directly indicates the edge of the workpiece. Move the beam to the edge of the work and set your dial to zero. It is that easy. No more calculating half the diameter of the edge finder. You can also use the Laser Center/Edge Finder™ to locate a scribed or center-punched location. Simply move the laser beam to the location on the workpiece and the spindle is aligned. The Laser Center/Edge Finder™ is easy to align, using the four alignment screws, so you can be sure it is always accurate. A target card and allen wrench are included to help with alignment. The batteries last for over 3 hours of continuous operation. That is about 6 months to a year of normal use.
Add to cart Details
Battery Powered Original LC/EF – 1/2″ Shank – Concentric Circle

$164.50
1/2" Shank is made for standard sized mills and lathes

3.375" overall length (without polarizer)

3/4" overall diameter

Uses three common LR44 batteries (included)

Repeatable Accuracy of .001" (estimated)

Includes dual polarizing attachment to minimize the thickness of the lines

The Laser Center/Edge Finder™ is a tool for your standard size mill, lathe or drill press which saves setup time. It eliminates the frustrations and doubts of using the century-old indirect method with a conventional edge finder or wiggler. The Laser Center/Edge Finder™ projects a series of concentric rings, making it easy to center over an existing hole.. The unit comes with a dual polarizer attached to allow the user to minimize the thickness of the lines for added accuracy. The Laser Center/Edge Finder™ is easy to align, using the four alignment screws, so you can be sure it is always accurate.. A target card and allen wrench are included to help with alignment. The batteries last for over 3 hours of continuous operation. That's about 6 months to a year of normal use.
Add to cart Details
A/C Bridgemount – no shank – Crosshair

$261.50

• Made for permanent installation on waterjet and wood CNC machines (gantry type) • Repeatable Accuracy of .001 (estimated) • AC Powered 110 or 240 VAC (power supply included) • Includes dual polarizing attachment to minimize the thickness of the lines The Bridgemount Laser Center/Edge Finder™ is a tool that is meant to be permanently attached to the gantry of a waterjet or wood CNC machine, using the offset command on the computer to move it to the starting point. This is a simple and fast way to find the edge of the workpiece or some other designated point. The Laser Center/Edge Finder™ projects a crosshair, making it easy to align a workpiece on the table. The unit comes with a dual polarizer attached to allow the user to minimize the thickness of the lines for added accuracy. The Laser Center/Edge Finder™ is easy to align, using the four alignment screws, so you can be sure it is always accurate. A target card and allen wrench are included to help with alignment. This AC Powered model comes with a screw-in connection.

Add to cart Details
Battery Powered WaterJet LC/EF to fit .281 nozzle (Flow) Solid Shank – Dot

$134.50
.281 mm shank made for waterjet machines with .281 nozzle (i.e. Flow)

Solid shank requires the removal of the nozzle

3.375" overall length (without polarizer)

3/4" overall diameter

Uses three common LR44 batteries (included)

Repeatable Accuracy of .001" (estimated)

Includes dual polarizing attachment to minimize the thickness of the lines

The Laser Center/Edge Finder™ is a tool for your waterjet machine which saves setup time. It eliminates the frustrations and doubts of using the century-old method with a conventional edge finder or wiggler. The Laser Center/Edge Finder™ projects a crosshair, making it easy to align a workpiece on the table. The unit comes with a dual polarizer attached to allow the user to minimize the thickness of the lines for added accuracy. The Laser Center/Edge Finder™ is easy to align, using the four alignment screws, so you can be sure it is always accurate. A target card and allen wrench are included to help with alignment. The batteries last for over 3 hours of continuous operation. That's about 6 months to a year of normal use.
Add to cart Details
Battery Powered Original LC/EF – 3/8″ Shank – Crosshair

$164.50
3/8" Shank is made for standard sized mills and lathes

3.375" overall length (without polarizer)

3/4" overall diameter

Uses three common LR44 batteries (included)

Repeatable Accuracy of .001" (estimated)

Includes dual polarizing attachment to minimize the thickness of the lines

The Laser Center/Edge Finder™ is a tool for your standard size mill, lathe or drill press which saves setup time. It eliminates the frustrations and doubts of using the century-old indirect method with a conventional edge finder or wiggler. The Laser Center/Edge Finder™ projects a crosshair, making it easy to align a workpiece on the table. The unit comes with a dual polarizer attached to allow the user to minimize the thickness of the lines for added accuracy. The Laser Center/Edge Finder™ is easy to align, using the four alignment screws, so you can be sure it is always accurate.. A target card and allen wrench are included to help with alignment. The batteries last for over 3 hours of continuous operation. That's about 6 months to a year of normal use.
Add to cart Details
Replacement Batteries (Set of 3) (LR-44)

$4.50
Fits all Laser Center/Edge Finder™ battery powered models

LR44 batteries 1.5 V each
Add to cart Details
Battery Powered Mini LC/EF – 1/4″ Shank – Crosshair

$164.50
1/4" Shank is made for mini tabletop mills/lathes

3" overall length (without polarizer)

3/4" overall diameter

Uses three common LR44 batteries (included)

Repeatable Accuracy of .001" (estimated)

Includes dual polarizing attachment to minimize the thickness of the lines

The Laser Center/Edge Finder™ is a tool for your mini tabletop mill/lathe which saves setup time. It eliminates the frustrations and doubts of using the century-old indirect method with a conventional edge finder or wiggler. The Laser Center/Edge Finder™ projects a crosshair, making it easy to align a workpiece on the table. The unit comes with a dual polarizer attached to allow the user to minimize the thickness of the lines for added accuracy. The Laser Center/Edge Finder™ is easy to align, using the four alignment screws, so you can be sure it is always accurate.. A target card and allen wrench are included to help with alignment. The batteries last for over 3 hours of continuous operation. That's about 6 months to a year of normal use.
Add to cart Details